Short Description

Model No.: Nickel-200/201-WNRF-Flange-8"-SCH80S-Class-600

China Welding Neck Flange Manufacturer www.metallicsteel.com offers ANSI B16.5 ASTM B564 Nickel 200/201 WNRF Flange, 8″, SCH80S, Class 600.

Request a quote Share

Key Specifications / Features

Type: WNRF Flange
Material: Nickel 200/Nickel 201 (UNS N02200/UNS N02201)
Pressure: 600#
Size: DN200 (8″)
Standard: ANSI B16.5
Ends: Raised Face

201810172050437217822 - ANSI B16.5 ASTM B564 Nickel 200/201 WNRF Flange 8" SCH80S Class 600

ASTM B564 200 / 201 Nickel Pipe Flanges Equivalent Grades

STANDARD UNS WERKSTOFF NR. AFNOR EN JIS BS GOST
Nickel 200 N02200 2.4066 N-100M Ni 99.2 NW 2200 NA 11 НП-2
Nickel 201 N02201 2.4068 LC-Ni 99 NW 2201 NA 11 НП-2

Nickel UNS N02200 / N02201 Flanges Chemical Composition

Grade NI FE CU C MN S SI
Nickel Alloy 200 99.0 min .40 max .25 max .15 max .35 max .01 max .35 max
  NI FE CU C MN S SI
Nickel Alloy 201 99.0 min .40 max .25 max .02 max> .35 max .01 max .35 max

Nickel Alloy WERKSTOFF NR. 2.4066 / 2.4068 ASME, DIN, BS, EN Flanges Mechanical Properties

Grade Density Yield Strength (0.2%Offset) Tensile Strength Elongation Melting Point
Nickel Alloy 200 / 201 8.9 g/cm3 Psi – 21500 , MPa – 148 Psi – 67000 , MPa – 462 45 % 1446 °C (2635 °F)

Dimensions of ANSI/ASME B16.5 Class 600 Weld Neck Flange

20189262231568412448 1 1 - ANSI B16.5 ASTM B564 Nickel 200/201 WNRF Flange 8" SCH80S Class 600

ANSI/ASME/ASA B16.5 600lb/sq.in. WELDING NECK FLANGE RF
ø D b g m a J* h k Holes l Kg.
1/2″ 95,2 14,3 34,9 38,1 21,3 15,7 52,4 66,7 4 15,9 0,900
3/4″ 117,5 15,9 42,9 47,6 26,7 20,9 57,1 82,5 4 19,0 1,500
1″ 123,8 17,5 50,8 54,0 33,5 26,7 61,9 88,9 4 19,0 1,900
1 1/4″ 133,3 20,6 63,5 63,5 42,2 35,0 66,7 98,4 4 19,0 2,600
1 1/2″ 155,6 22,2 73,0 69,8 48,3 40,9 69,8 114,3 4 22,2 3,300
2″ 165,1 25,4 92,1 84,1 60,3 52,6 73,0 127,0 8 19,0 4,700
2 1/2″ 190,5 28,6 104,8 100,0 73,1 62,7 79,4 149,2 8 22,2 6,500
3″ 209,5 31,7 127,0 117,5 88,9 78,0 82,5 168,3 8 22,2 8,700
3 1/2″ 228,6 34,9 139,7 133,3 101,6 90,1 85,7 184,1 8 25,4 11,200
4″ 273,0 38,1 157,2 152,4 114,3 102,4 101,6 215,9 8 25,4 18,100
5″ 330,2 44,4 185,7 188,9 141,2 128,2 114,3 266,7 8 28,6 30,500
6″ 355,6 47,6 215,9 222,2 168,4 154,2 117,5 292,1 12 28,6 36,200
8″ 419,1 55,6 269,9 273,0 219,1 202,7 133,3 349,2 12 31,7 56,500
10″ 508,0 63,5 323,8 342,9 273,0 254,5 152,4 431,8 16 34,9 91,000
12″ 558,8 66,7 381,0 400,0 323,8 304,8 155,6 488,9 20 34,9 105,000
14″ 603,2 69,8 412,7 431,8 355,6 * 165,1 527,0 20 38,1 125,000
16″ 685,8 76,2 469,9 495,3 406,4 177,8 603,2 20 41,3 178,000
18″ 742,9 82,5 533,4 546,1 457,2 184,1 654,0 20 44,4 261,000
20″ 812,8 88,9 584,2 609,6 508,0 190,5 723,9 24 44,4 268,000
22″ 869,9 95,2 641,2 666,7 558,8 196,8 777,9 24 47,6 328,000
24″ 939,8 101,6 692,1 717,5 609,6 203,2 838,2 24 50,8 380,000
* The data “J” corresponds to the STD schedule
To be specifiedby customer
NOTE:
1. Class 600 flanges except Lap Joint will be furnished with 0.25 (6.35mm) raised face, which is not included in ‘Thickness’ (C) and ‘Length through Hub’ (Y1), (Y3).
2. For Slip-on, Threaded, Socket Welding and Lap Joint Flanges, the hubs can be shaped either vertical from base to top or tapered within the limits of 7 degrees.
3. Blind Flanges may be made with the same hub as that used for Slip-on Flanges or without hub.
4. The gasket surface and backside (bearing surface for bolting) are made parallel within 1 degree. To accomplish parallelism, spot facing is carried out according to MSS SP-9, without reducing thickness (C).
5. Dimensions of sizes 1/2 through 3 1/2 are the same as for Class 400 Flanges.
6. Depth of Socket (D) is covered by ANSI B 16.5 only in sizes through 3 inch, over 3 inch is at the manufacturer’s option.
7. Welding Neck Flange Bore Size SCH10, SCH20, SCH30, STD, SCH40, SCH60, SCH80, SCH100, SCH 120, SCH140, SCH160, XS

Note: Welding Neck bore is derived from the pipe schedule

This method is used for detection of welding discontinuities (material discontinuities) appearing on the surface of a welded connector. This test is done following a visual testing of a welded connector and used mainly for both ferromagnetic and non-ferromagnetic materials.

PT – PENETRATION TESTING

20181091828401311297 1 2 - ANSI B16.5 ASTM B564 Nickel 200/201 WNRF Flange 8" SCH80S Class 600

Request a quote

Subject:

Products Related to ANSI B16.5 ASTM B564 Nickel 200/201 WNRF Flange 8″ SCH80S Class 600